Electronic universal testing machine is currently a relatively common teaching and testing equipment, mainly for universities, research institutions and so on. Because of its teaching purpose, its use rate is relatively high. Therefore, the frequent use of electronic universal testing opportunities leads to shortened service life. Therefore, proper and effective maintenance is particularly important. Jiangsu Tianhui tensile testing machine here to share the correct way to maintain and maintain the electronic universal testing machine.
First, the machine accessories (fixtures) should be coated with anti-rust oil;
Second, regular inspection of the machine for oil leakage, if there is oil leakage, should immediately replace the mat or seal, and according to the use of the machine and the use of oil, regular replacement filter, suction filter and hydraulic oil.
Third, each test should be completed after the test machine jaws to clean up, keep it clean.
Fourth, if it is not a machine for a long time, you should turn off the computer and controller. Regularly check the configuration of the machine and keep the machine in good working condition. If parts are loose and fall off, they should be repaired in time. The interface on the plug-in controller must turn off the power of the controller. The interfaces on the controller are one-to-one. If there is a wrong interface, the device may be damaged. If the machine is in the standby state, the switch should be “loadedâ€. Because if the switch is in the “reverse†position, the solenoid valve is always on, which will affect the life of the device.
5. Regularly inspect the screws at the jaws. If any looseness is found, tighten it in time and check the transmission condition of the sprocket regularly. If there is any looseness, tighten the tensioning wheel.
6. The sliding surface that is in contact with the steel plate and the liner plate and the dovetail groove surface on the liner shall be kept clean from time to time, and a thin layer of molybdenum disulfide (MoS2) grease shall be regularly coated; the electronic universal testing machine is currently the more common teaching method. Testing equipment is mainly provided to universities and research institutes. Because of its teaching purpose, its use rate is relatively high. Therefore, the frequent use of electronic universal testing opportunities leads to shortened service life. Therefore, proper and effective maintenance is particularly important. Jiangsu Tianhui tensile testing machine here to share the correct way to maintain and maintain the electronic universal testing machine.
First, the machine accessories (fixtures) should be coated with anti-rust oil;
Second, regular inspection of the machine for oil leakage, if there is oil leakage, should immediately replace the mat or seal, and according to the use of the machine and the use of oil, regular replacement filter, suction filter and hydraulic oil.
Third, each test should be completed after the test machine jaws to clean up, keep it clean.
Fourth, if it is not a machine for a long time, you should turn off the computer and controller. Regularly check the configuration of the machine and keep the machine in good working condition. If parts are loose and fall off, they should be repaired in time. The interface on the plug-in controller must turn off the power of the controller. The interfaces on the controller are one-to-one. If there is a wrong interface, the device may be damaged. If the machine is in the standby state, the switch should be “loadedâ€. Because if the switch is in the “reverse†position, the solenoid valve is always on, which will affect the life of the device.
5. Regularly inspect the screws at the jaws. If any looseness is found, tighten them in time and check the transmission condition of the sprocket regularly. If there is any looseness, tighten the tension pulley again;
6. The sliding surface that is in contact with the steel plate and the liner plate and the dovetail groove surface on the liner shall be kept clean from time to time, and a thin layer of molybdenum disulfide (MoS2) grease shall be regularly coated; the electronic universal testing machine is currently the more common teaching method. Testing equipment is mainly provided to universities and research institutes. Because of its teaching purpose, its use rate is relatively high. Therefore, the frequent use of electronic universal testing opportunities leads to shortened service life. Therefore, proper and effective maintenance is particularly important. Jiangsu Tianhui tensile testing machine here to share the correct way to maintain and maintain the electronic universal testing machine.
First, the machine accessories (fixtures) should be coated with anti-rust oil;
Second, regular inspection of the machine for oil leakage, if there is oil leakage, should immediately replace the mat or seal, and according to the use of the machine and the use of oil, regular replacement filter, suction filter and hydraulic oil.
Third, each test should be completed after the test machine jaws to clean up, keep it clean.
Fourth, if it is not a machine for a long time, you should turn off the computer and controller. Regularly check the configuration of the machine and keep the machine in good working condition. If parts are loose and fall off, they should be repaired in time. The interface on the plug-in controller must turn off the power of the controller. The interfaces on the controller are one-to-one. If there is a wrong interface, the device may be damaged. If the machine is in the standby state, the switch should be “loadedâ€. Because if the switch is in the “reverse†position, the solenoid valve is always on, which will affect the life of the device.
5. Regularly inspect the screws at the jaws. If any looseness is found, tighten them in time and check the transmission condition of the sprocket regularly. If there is any looseness, tighten the tension pulley again;
6. The sliding surface in contact with the lining plate and the liner plate and the dovetail groove surface on the lining plate shall be kept clean at all times, and a thin layer of molybdenum disulfide (MoS2) grease shall be regularly applied.
First, the machine accessories (fixtures) should be coated with anti-rust oil;
Second, regular inspection of the machine for oil leakage, if there is oil leakage, should immediately replace the mat or seal, and according to the use of the machine and the use of oil, regular replacement filter, suction filter and hydraulic oil.
Third, each test should be completed after the test machine jaws to clean up, keep it clean.
Fourth, if it is not a machine for a long time, you should turn off the computer and controller. Regularly check the configuration of the machine and keep the machine in good working condition. If parts are loose and fall off, they should be repaired in time. The interface on the plug-in controller must turn off the power of the controller. The interfaces on the controller are one-to-one. If there is a wrong interface, the device may be damaged. If the machine is in the standby state, the switch should be “loadedâ€. Because if the switch is in the “reverse†position, the solenoid valve is always on, which will affect the life of the device.
5. Regularly inspect the screws at the jaws. If any looseness is found, tighten it in time and check the transmission condition of the sprocket regularly. If there is any looseness, tighten the tensioning wheel.
6. The sliding surface that is in contact with the steel plate and the liner plate and the dovetail groove surface on the liner shall be kept clean from time to time, and a thin layer of molybdenum disulfide (MoS2) grease shall be regularly coated; the electronic universal testing machine is currently the more common teaching method. Testing equipment is mainly provided to universities and research institutes. Because of its teaching purpose, its use rate is relatively high. Therefore, the frequent use of electronic universal testing opportunities leads to shortened service life. Therefore, proper and effective maintenance is particularly important. Jiangsu Tianhui tensile testing machine here to share the correct way to maintain and maintain the electronic universal testing machine.
First, the machine accessories (fixtures) should be coated with anti-rust oil;
Second, regular inspection of the machine for oil leakage, if there is oil leakage, should immediately replace the mat or seal, and according to the use of the machine and the use of oil, regular replacement filter, suction filter and hydraulic oil.
Third, each test should be completed after the test machine jaws to clean up, keep it clean.
Fourth, if it is not a machine for a long time, you should turn off the computer and controller. Regularly check the configuration of the machine and keep the machine in good working condition. If parts are loose and fall off, they should be repaired in time. The interface on the plug-in controller must turn off the power of the controller. The interfaces on the controller are one-to-one. If there is a wrong interface, the device may be damaged. If the machine is in the standby state, the switch should be “loadedâ€. Because if the switch is in the “reverse†position, the solenoid valve is always on, which will affect the life of the device.
5. Regularly inspect the screws at the jaws. If any looseness is found, tighten them in time and check the transmission condition of the sprocket regularly. If there is any looseness, tighten the tension pulley again;
6. The sliding surface that is in contact with the steel plate and the liner plate and the dovetail groove surface on the liner shall be kept clean from time to time, and a thin layer of molybdenum disulfide (MoS2) grease shall be regularly coated; the electronic universal testing machine is currently the more common teaching method. Testing equipment is mainly provided to universities and research institutes. Because of its teaching purpose, its use rate is relatively high. Therefore, the frequent use of electronic universal testing opportunities leads to shortened service life. Therefore, proper and effective maintenance is particularly important. Jiangsu Tianhui tensile testing machine here to share the correct way to maintain and maintain the electronic universal testing machine.
First, the machine accessories (fixtures) should be coated with anti-rust oil;
Second, regular inspection of the machine for oil leakage, if there is oil leakage, should immediately replace the mat or seal, and according to the use of the machine and the use of oil, regular replacement filter, suction filter and hydraulic oil.
Third, each test should be completed after the test machine jaws to clean up, keep it clean.
Fourth, if it is not a machine for a long time, you should turn off the computer and controller. Regularly check the configuration of the machine and keep the machine in good working condition. If parts are loose and fall off, they should be repaired in time. The interface on the plug-in controller must turn off the power of the controller. The interfaces on the controller are one-to-one. If there is a wrong interface, the device may be damaged. If the machine is in the standby state, the switch should be “loadedâ€. Because if the switch is in the “reverse†position, the solenoid valve is always on, which will affect the life of the device.
5. Regularly inspect the screws at the jaws. If any looseness is found, tighten them in time and check the transmission condition of the sprocket regularly. If there is any looseness, tighten the tension pulley again;
6. The sliding surface in contact with the lining plate and the liner plate and the dovetail groove surface on the lining plate shall be kept clean at all times, and a thin layer of molybdenum disulfide (MoS2) grease shall be regularly applied.
Elbow Laser Cutting Machine:
1. Specialized for elbow port processing: flat mouth, open hole, 90° slitting, 45° slitting
2. Patented mold design, no loose clamping, high cutting precision
3. The three-dimensional pattern can be modified at any time, saving the cost of making and modifying the stamping die, with higher efficiency and better quality
4. Standard slag extraction module, the inner wall of the pipe is clean and free of iron slag
5. Applicable to a variety of metal materials: carbon steel, stainless steel, aluminum alloy, copper, etc.
2. Patented mold design, no loose clamping, high cutting precision
3. The three-dimensional pattern can be modified at any time, saving the cost of making and modifying the stamping die, with higher efficiency and better quality
4. Standard slag extraction module, the inner wall of the pipe is clean and free of iron slag
5. Applicable to a variety of metal materials: carbon steel, stainless steel, aluminum alloy, copper, etc.
6. The main part of the machine tool is the main part of the whole elbow pipe cutting machine. The cutting function and cutting accuracy of the elbow pipe cutting machine are realized by the main machine part. It is composed of the mechanism and the top positive slag extraction mechanism, auxiliary system (lubrication, gas circuit and water circuit), electric control cabinet, operation screen, operation panel and other parts.
7. The patented design of the mold can solve the industry pain points of poor positioning, unstable clamping and poor cutting accuracy. The clamping is not loose. And the cutting accuracy is high.
8. High adaptability: It has a variety of optical fiber interfaces and is compatible with various mainstream lasers.
Excellent design: Optimized optical configuration and smooth and efficient airflow design significantly improve cutting quality and efficiency.
Slim nozzle design: Modular, slim nozzle design reduces workpiece interference.
Compact structure: extremely light weight and small size, reducing robot load requirements and improving cutting speed and quality.
Elbow Laser Cutting,Elbow Laser Cutting Machine,Elbow Tube Laser Cutting Machine,Elbow Machine For Sales
GUANGDONG CHITTAK INTELLIGENT EQUIPMENT CO.,LTD , https://www.ctklasercutting.com